Sound Fx

home *** CD-ROM | disk | FTP | other *** search

/ Sound Fx / Sound Fx.iso / Software / UNZIPED / SWL / SWLINDOO < prev

Wrap

Internet Message Format | 1993-11-08 | 11.5 KB

From: info-serv@arrl.org (ARRL HQ AUTOMATED ELECTRONIC MAIL SERVER) Subject: INFO response: SWL-INDOOR-ANT Indoor SWL antenna article - "Carpet Loop Antenna" Newsgroups: rec.radio.shortwave,rec.radio.amateur.misc From: moisan@silver.lcs.mit.edu (David Moisan) Subject: Carpet Loop Antenna THE CARPET LOOP II -- A High Performance Indoor Antenna ------------------------------------------------------- Designed by David Moisan, N1KGH Introduction: ------------- There are many shortwave listeners who can't, because of location, infirmity or a unyielding landlord, put up an outside antenna. Such people are given two choices--random wire or active antenna. Yet, for the serious listener, neither choice is completely adequate. Active antennas are expensive, apt to generate as much noise as signal, and are prone to overload. Random wires are cheap (cheapest, in fact) and easy to put up, but are unpredictable performers. Both subject the receiver to intermod, spurious signals and other trash. The Carpet Loop II is an ideal step upward for the listener who wants something better than a random wire but doesn't want the expensive dice roll of an active antenna. The Carpet Loop is made up of two components: A tuner, and the antenna cable itself; the cable can be either 5-conductor rotator cable or 4-conductor flat phone cable, both readily available from Radio Shack and elsewhere. The tuner couples the antenna to the radio, forming a (giant!) L-network. To tune the antenna, you turn a switch for best reception. While NO antenna can give a cheap receiver the sensitivity, selectivity, or dynamic range it never had, the Carpet Loop will help you get the last ounce of performance out of your radio. Two years ago, I was using a random wire. I had severe problems with a local AM station (2 miles away) on 1230 Khz. I was hearing intermod from it all over the 9 to 12 Mhz range. With the Carpet Loop (which was then just the cable), the interference was almost completely gone. Also, the signals I was receiving seemed to be just a little bit stronger. A year later, I built the tuner, with much better results. I'm convinced I have the best possible antenna for my location. If you're stuck in an apartment, if you have a portable like the Sony 2010, the Sangean 803A or the Radio Shack DX400 or 440, if you have a tabletop receiver, the Carpet Loop may be for you. It's cheap--around $25 in parts from Radio Shack, *much* less if you shop around, and an excellent first project for the technically minded. CARPET LOOP II From Radio SCHEMATIC AND PARTS LIST Gnd. Ant. S1 1 pole 6 position ! ! rotary switch ! D1 ! (RS# 275-1386) !---->I----! +----------*----I<----! C1 365 pf variable ! ! D2 ! capacitor (see ! ! ! text) ! o o ! #A S2 SPST switch ! \ ! --- S2 \ --- C1 D1, D2 1N914 silicon ||| o --- switching diodes (Earth ! ! (RS# 276-112) Gnd.) ! ! #B ! ! J1, J2 6-position terminal ! ! strip (RS#274-357) +G-o <---o----+ ! Antenna cable: ! o S1 o ! !E !A 5-conductor rotator J1 ! ! o o ! J2 cable (RS#15-1201) ! ! !D o !B ! (see text) 1 |o|----* ! ! !C ! ! 2 |o|-------*--!--!--!--!-----|o| 6 Miscellaneous: 3 |o|----------*--!--!--!-----|o| 7 4 |o|-------------*--!--!-----|o| 8 Aluminum enclosure, 5 |o|----------------*--!-----|o| 9 spade lugs, connector |o| (not used) *-----|o| 10 and cable to radio (not used)|o| (see text), knobs <- To Antenna -> Note on Schematic symbols: ! -*- means: Intersecting wires are connected ! ! -!- means: Intersecting wires NOT connected ! HOW IT WORKS ------------ S1, C1, and the antenna cable connected to J1 and J2 form an L- network; when S1 is switched between positions A through F, and C1's capacitance is varied, the impedance of the antenna system changes. When S1 and C1 are adjusted for best signal, the impedance between antenna and receiver is matched. D1 and D2 provide protection against static discharges. The G position of S1 grounds the antenna when not in use. S2 disconnects the ground from the antenna, making the antenna into a random wire. TUNER CONSTRUCTION ------------------ PARTS AVAILABILITY: With the exception of C1, all parts for the tuner are readily available from Radio Shack. C1, the 365 pf variable capacitor, can be gotten out of an old radio. SUBSITUTIONS: There are no critical parts in the tuner; as long as S1 has at least six positions, it will do. D1 and D2 can be any silicon diode. Use any enclosure that's big enough to comfortably install components in. The choice for J3, the jack to the receiver, depends on what connector your radio uses for an external antenna. I used an SO-239 (RS #278-201); you could also use a TV antenna terminal strip (RS#274-663). STEP-BY-STEP INSTRUCTIONS: 1) Mount the components on the enclosure you'll be using--all wiring is point to point. I suggest mounting J1 and J2 on opposite sides, S1 and C1 on top, and J3 on the other end of the enclosure. 2) Wire S1 to J1 and J2. If you use the Radio Shack DP6T rotary switch, you'll be using just one of the poles. The diagram of the switch is below: D C S1 DP6T rotary E o o B switch G o o A | o o | Viewing from P |o o| bottom of switch | o o | o o o o Wire as follows: (Note: If you're using the Radio Shack terminal strip, you will need to drill a hole in the cabinet to pass the wires through from inside. Use a rubber grommet to keep the wires from fraying) S1 Term. --to--> J1 term. J1 term. --to--> J2 term. A #1 #2 #6 B #2 #3 #7 C #3 #4 #8 D #4 #5 #9 E #5 Connect a wire from J2 terminal #10 to the G terminal on S1, and this step is done. 3) Install and wire C1. Connect one terminal of C1 to the P terminal on S1. Connect the other end to J3. If using the SO239 or phono jack, connect to the center conductor. If using screw terminals, connect to terminal #1 on J3. Skip ahead to step 5. 4) Connect the P terminal of S1 to J3. If you're using the SO239 or phono jack, connect to the center conductor. If you're using screw terminals, connect to terminal #1 on J3. 5) Connect the G terminal on S1 to J3. Connect it to the ground shield if it's an SO239 or phono jack, or to terminal #2 if it's screw terminals. 6) Connect D1 and D2 across J3's terminals; remember that D2 is connected opposite of D1. That completes construction of the tuner. ANTENNA CONSTRUCTION -------------------- CHOOSING CABLE: The kind of cable you use depends on where you're putting it and and how much you want to pay for the cable. If you plan on running it under carpet, then use the 5-conductor rotator cable mentioned in the parts list. This cable can easily withstand being stepped on; more importantly, there are no exposed wires to trip over. It's also easier to wire than phone cable. If you're not running it underfoot, or if you're cheap, you can use 4-conductor flat phone cable, available nearly everywhere. It's a good choice for running around baseboards, around windows or in attics. When running the cable around, start at your receiver and go around the room--or the house--and back to the radio. If you're using the rotator cable, you can make corners by folding the cable at a 45 degree angle, like folding paper. WIRING THE CABLE TO THE TUNER: You should have two ends of the cable next to the tuner. Strip the ends and put spade lugs on all the wires. With the rotator cable, mark the *silver* conductor. Next, connect the wire to the tuner using the following diagrams: FOR 5-CONDUCTOR ROTATOR CABLE FOR 4-CONDUCTOR PHONE CABLE J1 J2 J1 J2 1 1 1 2 3 4 5 6 7 8 9 0 1 2 3 4_5 6 7 8 9_0 ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ Wire S C C C C S C C C C B Y R G B Y R G colors (4&5 jumpered) (9&10 jumpered) ((S)ilver, (C)opper, (B)lack, (Y)ellow, (R)ed, (G)reen) GROUNDING: Run a wire--preferably a large one--from the ground terminal on the tuner (or a mounting screw on the SO239 connector if you're using one) to a suitable ground such as a cold water pipe; I grounded my tuner with a short length of RG58 coax connected to a baseboard heater via an alligator clip. Connect the tuner to your receiver; you are now ready to use it. USING THE CARPET LOOP --------------------- It's easier to use than to talk about: Tune your receiver to the desired frequency. Adjust S1 and C1 (or the antenna trimmer on the radio) for strongest signal. For most situations, S2 (Loop/Longwire) can be left closed in the Loop position; you may find that setting S2 to Longwire may work better for mediumwave listening. CONCLUSION ---------- The Carpet Loop II is an inexpensive, easily built, high performance antenna that can work in almost all apartments. CONTACTING THE AUTHOR --------------------- I can be reached at the following addresses: Mail: David Moisan 86 Essex St. Apt. #204 Salem, MA 01970-5225 Fidonet: David Moisan, 1:101/165 Internet: dmoisan@pro-angmar.alfalfa.com or moisan@silver.lcs.mit.edu Your comments and suggestions are welcome. -- | David Moisan, N1KGH /^\_/^\ dmoisan@pro-angmar.alfalfa.com | | 86 Essex St. Apt #204 ( o ^ o ) moisan@silver.lcs.mit.edu | | Salem. MA 01970-5225 | | | \-----------------------------------------------------------------/ The members and HQ staff would like to thank the following people for their contributions to this information file: n1kgh@amsat.org Send any additional information or changes to the author. 73 from ARRL HQ.